Shower splash guards are available in various sizes, compositions, and styles. They improve the appearance of your bathroom and are perfect for retaining the water in your bathtub or shower.
Two plastic sheets may be cut into triangles to create a shower splash shield. With silicone-based glue, attach the parts to the corners of the tub or shower, and you’re done! We’ll show you how to create your shower splash protector in this post, which you can then glue to the corners of your tub or shower.
How to Make a Shower Splash Guard Using Tile
You may block the water from passing the ends of your curtains by making shower splash guards using tile and tacking the pieces to the top of your tub at both ends.
Splash guards for showers purchased in stores are not composed of tile, and splash guards are typically made of plastic. However, plastic splash guards don’t go with your bathroom decor.
What You’ll Need
- Tiny, round paintbrush
- Thin wire
- Tile scribe
- Sandpaper
- Wood
- Saw
- Mortar
- Fork
- Construction glue
- Grout
- Bathroom caulk
- Grout adhesive
Instructions
Step 1
Start by dividing two tiles into triangles, and draw diagonal lines from one corner to the other.
Step 2
Cut the tiles along the markings using a tile scribe. Put a ruler against the mark and score the tile while applying pressure to simplify the cutting operation.
To split a tile in two, place a taut, straight wire underneath it and line it with the cut. Then, apply pressure, including both ends of the tile.
Step 3
To fit the tiles, prepare two triangle wood blocks. Making these blocks is as simple as cutting a cube out of a wooden block.
Create a square approximately 3/8 inch larger in both directions than the tiles, and cut it in half to create two triangles. Ensure that you also sand down the cut ends.
Step 4
Using a scribe, cut two rectangular tile parts to the exact dimensions as the measurements you took for the cut edge of one of the blocks.
Step 5
Apply mortar to the tile’s backs. Press the tiles together while roughening up the mortar with a fork, keeping the square edges of the blocks clean.
Allow the mortar to set up and solidify.
Step 6
With the help of a lot of construction adhesive, secure the tiled pieces to the tub’s corners. Before applying the grout to the crevices between the tubs, let the glue completely dry.
Step 7
Apply the grout, then use a moist sponge to remove any excess grout from your new splash guards. Then let it dry.
Step 8
Run a bead of caulk down the seam where the splash guard edges contact the tub. To even out the caulk, run your finger along it.
Step 9
After everything has had time to set completely, seal the grout.
How to Make a Shower Splash Guard Using Plastic
Shower splash guards may be made from plastic much more quickly and efficiently than from tile. So, if you want a quick cure, follow the instructions below.
What You’ll Need
- The plastic of your choice
- A knife or saw (depending on how thick your plastic is)
- Silicone-based adhesive
Instructions
Step 1
To divide two pages into triangles, create diagonal lines from one corner to the next.
Step 2
A sharp knife or saw should be used to slice the panels along the diagonal lines.
Step 3
Ensure that the sheet pieces match the contours of your shower or tub. You are prepared for the following stage if they are a good fit.
If not, trim the pieces to accommodate the corners of your bathtub or shower.
Step 4
Be careful to wash the areas with a damp sponge, soap, or rubbing alcohol before gluing the shower splash shields down.
After finishing, wait for the surface to dry before adding adhesive and splash guards. Finally, use a rubber seal band to prevent sharp edges.
Other Ways to Prevent Splashing from Your Shower
Employ one or all of the following techniques to stop water from escaping from your shower or bathtub, which might lead to floor damage.
Sloping Floors
To direct the water down the drain, it is not only helpful but also crucial to slope the shower floor in that direction.
A slope shouldn’t be steeper than 1/8 to 1/4 inch every foot. If not, it will be challenging for someone using a wheelchair to sit level when taking a shower.
Linear Drain
Another option is to put up a linear ditch drain, which often looks like a long, linear drain that gathers water and sits at the same height as the shower floor.
Rubber Threshold
A rubber threshold that collapses may be found around the front border of your shower and is also referred to as a water dam.
As it falls as people roll over it and then rises again to help stop the water from seeping, it is also excellent for persons who use wheeled mobility units.
Longer Shower Curtain
Choose a heavy-duty curtain or a shower curtain with weights. Ensure the length of the curtain is appropriate for the height of your shower and almost reaches the ground while remaining off the ground. Otherwise, the folds are liable to develop mildew.
Splash Guards for the Shower Curtain
Install splash guards if you decide to use shower curtains for additional safety.
To keep water from dripping through the curtain ends, they are often linked to the shower curtain’s loops or hooks and hold drapes closer to the wall.
Splash Clips
Additionally, these clips will stop the water from escaping from your shower. It’s simple to install them. Use a self-adhesive strip to adhere the clips to the wall.
The shower curtain’s ends will be secured to the wall by the time you close it the following time, keeping the water within the shower.
Install a Full-Length Shower Door
For complete security, you may add a full-size shower door. Doors provide a complete enclosure; thus, we think they function better than any of the alternatives above. Purchase shatter-resistant glass shower doors, nevertheless, to be safe.
Shower doors offer the most robust defense against water leaks, but they also risk breaking if built incorrectly or poorly designed.
Conclusion
So, there you have it! There are a couple of different ways you can prevent splashing from your shower. You can either make your own shower splash guard or simply just buy a prebuilt splash guard. Whatever you choose we hope this article has been helpful to you.