So, you have had the American Standard Vormax toilet installed in your home? Well done! It is a great choice not only because it is reasonably priced but also because it eliminates waste from your toilet bowl with just a single flush. This is because the toilet uses a whopping 1.28 gallons of water per flush.
However, this is not to say that you will not have issues when you choose to have this toilet installed. A good number of people have reported issues with the American Standard Vormax toilet. Some of them include the following:
Common Problems with The American Standard Vormax
Leaking Flapper
The first problem that most people notice is that their Vormax toilet has a leaky flapper. This is understandable, given that the flapper can become worn out over time and start leaking water into the bowl when you flush it. If you have this problem, there are several things you can do to fix it:
- Clean The Flapper – The best way to fix this problem is by cleaning out your toilet’s flapper and replacing it with a new one. To do this, turn off your water at the main valve and remove all visible debris from inside the tank before putting a new flapper in place.
- Replace The Flapper – If cleaning doesn’t work, then you may need to replace your flapper with an updated version that won’t leak as easily. You can buy replacements at most home improvement stores or even online by searching for them using keywords like “flappers.
Dirt and Sand Clogging in Toilet Bowl
Dirt and sand can clog up your toilet bowl and cause problems with the flushing action. It’s a common problem that plagues many homeowners.
If you realize that your toilet isn’t flushing properly, check if there is a clog in your toilet. To do this, turn off the water supply to your home and then open up the lid of the tank. If you see brown or black gunk coming out of your toilet, then you’ve got a clog in there that needs to be removed right away so that your toilet can flush properly again.
Loose Flush Valve Chain
A loose flapper chain can cause an intermittent water seal, which results in water not being able to fill the bowl to the proper height. This causes the toilet to flush slowly and weakly and may even break down completely.
To fix this problem, remove the tank lid and look for any signs of rust or other damage on the flapper chain. If you find any damage, replace it immediately with a new one that is made from stainless steel or another type of metal that will not corrode over time. You can also clean off any rust or dirt from your old toilet before installing a new flapper chain by using a rag soaked in vinegar or baking soda mixed with water.
Trip Lever Depression
Another common problem with the American Standard Vormax toilet is the trip lever depression. This is when the handle of the toilet will not lift up and down easily, causing you to have to push on it harder than usual in order to flush your toilet. A few things can cause this problem, including:
- A bad flapper valve – If your flapper valve is broken or worn out, it could be causing this issue with your toilet. If you want to fix this problem yourself, you can do it at home yourself or contact a plumber to do it for you.
- A broken handle – If you’ve removed old handles from older toilets and replaced them with new ones, they may have been installed improperly and were not torqued down properly. This can cause them to loosen over time which will cause them not to work properly as well.
- A dirty flapper valve – Some people find that their flush doesn’t work correctly because their flapper valve is dirty or clogged with hair or other debris. If this is the case, simply clean it off and continue using their toilet as normal.
Skewed Wax Ring
The wax ring is the seal that keeps water from leaking and prevents it from seeping out of the toilet bowl when it’s flushed. If the wax ring is not properly installed, water can leak into the base of your toilet, which will eventually damage your flooring.
The best way to fix this problem is to get a plumber to install a new wax ring for you, but in many cases, this isn’t necessary. You can fix a misaligned wax ring yourself by adjusting it so that it sits above the rim of your toilet bowl instead of below it.
To do this, unscrew one side of the existing wax ring and slide it toward the center of your toilet bowl until you feel resistance against one end of its metal rod. Then tighten this metal rod and repeat with the other side until both sides are firmly fastened to their respective rods, and they won’t move around anymore.
How Does the American Standard Vormax Toiler Work?
Standard flush toilets are a basic model. They have a standard flushing mechanism where you have to use the handle to push down the handle and pull it back up. The water is then forced out through the base of the toilet bowl.
But, if you want to go for the advanced features like dual-injection flush valves and a strong vortex, then you will need to opt for the VorMax series of toilets. These toilets also come with a unique system that helps get rid of any waste left behind in the bowl after using it, including under the rim.
How do you Prime an American Standard VorMax Toilet?
The process is quite easy.
- Step 1: You want to begin by adjusting the water level to the one indicated on your tank. This is done by turning the adjustment knob so that it moves the float cup. Turning it right will add to the water level while turning it left will lower the level.
- Step 2: You can now prime your toilet by flushing it at least five times. However, you may have to do this more or fewer times to get your toilet bowl primed.
What is VorMax Flush Technology?
It is a combination of a high-pressure pump and an advanced valve that works together to clean your toilet bowl every time you flush. The pump creates a powerful water stream that cleans all areas of your toilet bowl – even under the rim without wasting any water at all.
Is the VorMax Toilet Worth it?
Yes, it is. The VorMax is a great toilet because it’s both affordable and has high-quality features that make it great value for money.